The advanced Single Channel Sensor Kit that gives you speed. Accurately.

• Single Channel design measures motor shaft speed.
• Pre-gapped and adjusted at CONTREX. No phase or mechanical adjustment is required.
• Simply attach to your motor, hook up the wiring, and go. Very easy installation.
• Eliminates the need for special brackets and couplers.
• Unique design of sensor insert (not cylindrical, like others) creates a fixed sensor gap, providing more accurate readings.
• Square-cut design of gear teeth provides a greater measure of accuracy than rounded spur gears.
• Provides 60 pulses per revolution. So each gear tooth is 6º resolution of the total pulse rotation.
• Teamed up with an intelligent controller (CONTREX CX-1010, or other smart receivers) can interpret 120 edges or 3º resolution.
• Sizes range from 56C to 254TC and 71D Metric.
• Complete Single Channel Sensor Kit includes: flange ring, sensor, 60 tooth gear, junction box, electrical caps, wiring, bolts.

Single Channel Sensors and Ring Kits

• SENSOR TYPE: Hall Effect Speed Sensor
• PULSES PER REVOLUTION: 60 cycles each channel
• SENSING SPEED RANGE: Zero speed to 10,000 RPM (shaft speed)
• GAP ADJUSTMENT: None required
• OPERATING TEMPERATURE: 0º to 70º C
• SUPPLY VOLTAGE: +5 to +15 VDC or +15 to +24 VDC
• SUPPLY CURRENT: 20 mA @ +5 VDC; 40 mA @ +15 VDC
• SWITCHING FREQUENCY LIMIT: 100 kHz
• OUTPUT DRIVE TYPES: Differential, Open Collector, Open Collector with pull-up
• OUTPUT DRIVE CAPABILITY: 250 mA per channel continuous
• MAXIMUM LOAD: 70 ohms per channel @ +15 VDC

Literature

• Ring Specifications 56C and 143TC (PDF format, 437kb)
• Ring Specifications 182TC, 213TC and 245TC (PDF format, 447kb)
• Ring Specifications 71D (PDF format, 432kb)

Single Channel Sensor Ring Kits - 60 Tooth Gear - 5 to 15 VDC - Open Collector

• 7300-1430 56C, 5/8" Bore, with Pull-up Resistor
• 7300-1431 143TC, 7/8" Bore, with Pull-up Resistor
• 7300-1432 182TC, 1-1/8" Bore, with Pull-up Resistor
• 7300-1433 213TC, 1-3/8" Bore, with Pull-up Resistor
• 7300-1434 254TC, 1-5/8" Bore, with Pull-up Resistor
• 7300-1435 71D Metric, 14mm Bore, with Pull-up Resistor
• 7300-1440   56C, 5/8" Bore, without Pull-up Resistor
• 7300-1441 143TC, 7/8" Bore, without Pull-up Resistor
• 7300-1442 182TC, 1-1/8" Bore, without Pull-up Resistor
• 7300-1443   213TC, 1-3/8" Bore, without Pull-up Resistor
• 7300-1444   254TC, 1-5/8" Bore, without Pull-up Resistor
• 7300-1445 71D Metric, 14mm Bore, without Pull-up Resistor

Single Channel Sensor Ring Kits - 60 Tooth Gear - 5 to 15 VDC - Differential

• 7300-1450 56C, 5/8" Bore, Line Driver Output
• 7300-1451 143TC, 7/8" Bore, Line Driver Output
• 7300-1452 182TC, 1-1/8" Bore, Line Driver Output
• 7300-1453 213TC, 1-3/8" Bore, Line Driver Output
• 7300-1454 254TC, 1-5/8" Bore, Line Driver Output
• 7300-1455 71D Metric, 14mm Bore, Line Driver Output

Single Channel Sensor Ring Kits - 60 Tooth Gear - 15 to 24 VDC - Open Collector

• 7300-1460 56C, 5/8" Bore, with Pull-up Resistor
• 7300-1461 143TC, 7/8" Bore, with Pull-up Resistor
• 7300-1462 182TC, 1-1/8" Bore, with Pull-up Resistor
• 7300-1463 213TC, 1-3/8" Bore, with Pull-up Resistor
• 7300-1464 254TC, 1-5/8" Bore, with Pull-up Resistor
• 7300-1465 71D Metric, 14mm Bore, with Pull-up Resistor
• 7300-1470 56C, 5/8" Bore, without Pull-up Resistor
• 7300-1471 143TC, 7/8" Bore, without Pull-up Resistor
• 7300-1472 182TC, 1-1/8" Bore, without Pull-up Resistor
• 7300-1473 213TC, 1-3/8" Bore, without Pull-up Resistor
• 7300-1474 254TC, 1-5/8" Bore, without Pull-up Resistor
• 7300-1475 71D Metric, 14mm Bore, without Pull-up Resistor